Meadows 4" Board Edgers

Meadows 4" Board Edgers are available in handset or hydraulic models. The hydraulic edgers are available with manual valves or electric valves with push button controls. Our 4" edgers are available in 30" and 36" widths. The chart below provides a quick reference of the features on each of our 4" edgers. If you have further questions or wish to inquire about prices please contact Bob, Brian, or Robert at 1-800-626-2282 or 336-838-2282.

Meadows 4" Standard Edgers	Meadows 4" Deluxe Edgers	Meadows 4" Titan Edgers
Frame Construction: 6" steel channel side rails with welded tubular cross members 20' length with standard 8' infeed and 8' outfeed 30" or 36" width 2 pairs of legs constructed from 6" channel	Frame Construction: 6" steel channel side rails with welded tubular cross members 20' length with standard 8' infeed and 8' outfeed 30" or 36" width 2 pairs of legs constructed from 6" channel	Frame Construction: 8" steel channel reinforced with 6" channel cross members 20' length with standard infeed and outfeed Hood assembly with 3/8" side plates and 1/4" top doors 36" width only 2 pairs of legs constructed from 6" channel
Mandrel: 2 3/16" diameter high carbon turned, ground and polished steel with two 1/2" keys Two 1 11/16" pillow block bearings	Mandrel: 2 15/16" diameter high carbon turned, ground and polished steel with two 1/2" keys Two 2 3/16" pillow block bearings	Mandrel: 2 15/16" diameter high carbon turned, ground and polished steel with two 1/2" keys Two 2 3/16" pillow block bearings
Feed Rolls and Press Rolls: Two 2 3/16" diameter corrugated infeed and two 2 3/16" corrugated outfeed bottom rolls connected by a roller chain drive Double v-belt feed from mandrel to feed pulley 1 11/16" pillow block bearings Two 5 1/2" diameter overhead press rolls Complete set of anti-kickback fingers with release handle	Feed Rolls and Press Rolls: Two 2 15/16" diameter corrugated infeed and two 2 15/16" diameter outfeed bottom rolls connected by a roller chain drive Double v-belt feed from mandrel to feed pulley Optional variable speed hydraulic feed 1 11/16" pillow block bearings Two 5 1/2" diameter overhead press rolls Complete set of anti-kickback fingers with release handle	Feed Rolls and Press Rolls: Two 2 15/16" diameter corrugated infeed and two 2 15/16" diameter outfeed bottom rolls connected by a roller chain drive Double v-belt feed from mandrel to feed pulley Optional variable speed hydraulic feed 1 11/16" pillow block bearings Two 5 1/2" diameter overhead press rolls Complete set of anti-kickback fingers with release handle
Rate of Feed: 129 feet per minute at 2000 RPM for handset models	Rate of Feed: 129 feet per minute at 2000 RPM for handset models Variable for hydraulic models	Rate of Feed: 129 feet per minute at 2000 RPM for handset models Variable for hydraulic models
Saws: 16" inserted tooth saw, 8 gauge with 14 teeth, 9/32" kerf, 3 1/4" eye with three 9/16" pin holes on a 4" circle 16" split carbide saws, 10 gauge with 18 teeth, 0.204" kerf	Saws: 16" inserted tooth saw, 8 gauge with 14 teeth, 9/32" kerf, 3 1/4" eye with three 9/16" pin holes on a 4" circle 16" split carbide saws, 10 gauge with 18 teeth, 0.204" kerf	Saws: 16" inserted tooth saw, 8 gauge with 14 teeth, 9/32" kerf, 3 1/4" eye with three 9/16" pin holes on a 4" circle 16" split carbide saws, 10 gauge with 18 teeth, 0.204" kerf
Capacity: Width capacity for 30" Edger is 30 3/4", and for a 36" edger is 35 3/4", Cut depth from 1" to 4 1/2"	Capacity: Width capacity for 30" Edger is 30 3/4", and for a 36" edger is 35 3/4", Cut depth from 1" to 4 1/2"	Capacity: Width capacity varies based on configuration Cut depth from 1" to 4"
Mandrel Speed Recommended: 2000 to 2400 RPM	Mandrel Speed Recommended: 2000 to 2400 RPM	Mandrel Speed Recommended: 2000 to 2400 RPM
Power Required: Generally 30-hp to 50-hp, however, horsepower requirements may vary with saw configurations and thickness of material to be edged	Power Required: Generally 30-hp to 50-hp, however, horsepower requirements may vary with saw configurations and thickness of material to be edged	Power Required: Generally 30-hp to 50-hp, however, horsepower requirements may vary with saw configurations and thickness of material to be edged
Optional Equipment: Hydraulic saw shift Variable speed hydraulic feed Laser lights Wheel mounting Movable fence Saw dust blower Electric motor, starter, and v-belt drive	Optional Equipment: Hydraulic saw shift Variable speed hydraulic feed Laser lights Wheel mounting Movable fence Saw dust blower Live outfeed rolls Tailing device, standard 16' x 5" driven from the edger Electric motor, starter, and v-belt drive	Optional Equipment: Hydraulic saw shift Variable speed hydraulic feed Laser lights Movable fence Saw dust blower Live outfeed rolls Tailing device, standard 16' x 5" driven from the edger Electric motor, starter, and v-belt drive