| Meadows 6"
Spartan |
Meadows 7"
Trojan |
Meadows 8 1/2"
Hercules |
Frame Construction:
- Frame constructed from stacked 8" x 18.75 lb./ft.channel.
- Side Plates are precision laser cut from 1/2" sheet
- Edger hood is totally enclosed and operator is protected by a full
bay of 1/2" thick x 2" wide anti-kickback fingers
- Center section stands on 4 legs of 3" x 4" x 1/4"
rectangular tubing with 1/2" plates for lagging or welding
machine to floor
- Standard frame length is 20' with infeed and outfeed table
|
Frame Construction:
- Frame constructed from stacked 8" x 18.75 lb./ft.channel.
- Side Plates are precision laser cut from 1/2" sheet
- Edger hood is totally enclosed and operator is protected by a full
bay of 1/2" thick x 2" wide anti-kickback fingers
- Center section stands on 4 legs of 3" x 4" x 1/4"
rectangular tubing with 1/2" plates for lagging or welding
machine to floor
- Standard frame length is 20' with infeed and outfeed table
|
Frame Construction:
- Frame constructed from stacked 8" x 18.75 lb./ft.channel.
- Side Plates are precision laser cut from 1/2" sheet
- Edger hood is totally enclosed and operator is protected by a full
bay of 1/2" thick x 2" wide anti-kickback fingers
- Center section stands on 4 legs of 3" x 4" x 1/4"
rectangular tubing with 1/2" plates for lagging or welding
machine to floor
- Standard frame length is 20' with infeed and outfeed table
|
Table Rolls:
- 4" O.D. (Schedule 40 pipe with 1/4" wall) with 1"
shaft with 1" pillow block bearings
|
Table Rolls:
- 5 9/16" O.D. (Schedule 40 pipe with 1/4" wall) with 1
7/16" shaft with 1 7/16" pillow block bearings
|
Table Rolls:
- 5 9/16" O.D. (Schedule 40 pipe with 1/4" wall) with 1
7/16" shaft with 1 7/16" pillow block bearings
|
Mandrel:
- 2 15/16" diameter high carbon turned, ground and polished
steel with two 1/2" keys
- Two 2 15/16" four-bolt flange bearings on side plates
- One 2 3/16" pillow block bearing on outboard bearing
|
Mandrel:
- 2 15/16" diameter high carbon turned, ground and polished
steel with two 1/2" keys
- Two 2 15/16" four-bolt flange bearings on side plates
- One 2 3/16" pillow block bearing on outboard bearing
|
Mandrel:
- 3 7/16" diameter high carbon turned, ground and polished
steel with two 5/8" keys
- One 3 7/16" four-bolt flange bearings on side plate on the
outboard bearing side
- One 2 15/16" four-bolt flange bearing on the door
- One 2 15/16" pillow block bearing on outboard bearing
|
Feed Rolls and Press Rolls:
- Two 3" diameter machine-cut infeed and two 3" diameter
machine-cut outfeed bottom rolls connected by a roller chain
drive
- Feed rolls mounted with 1 11/16" four-bolt flange bearings
- Hydraulic feed with variable control
- Two 5" diameter (Schedule 40 pipe with 1/4" wall) overhead
press rolls with 1 7/16" shafts
- Press roll mounted with 1 7/16" bearing insert with locking
collar
- Standard Hydraulic press roll lift with foot-pedal control or push
button
- Optional automatic press roll lift with photoelectric eyes
- Complete set of anti-kickback fingers with release handle, 48"
edgers are standard with two release handles
|
Feed Rolls and Press Rolls:
- Two 4" diameter machine-cut infeed and two 4" diameter
machine-cut outfeed bottom rolls connected by a roller chain
drive
- Feed rolls mounted with 1 15/16" four-bolt flange bearings
- Hydraulic feed with variable control
- Two 5" diameter (Schedule 40 pipe with 1/4" wall) overhead
press rolls with 1 7/16" shafts
- Press roll mounted with 1 7/16" bearing insert with locking
collar
- Standard Hydraulic press roll lift with foot-pedal control or push
button
- Optional automatic press roll lift with photoelectric eyes
- Complete set of anti-kickback fingers with release handle, 48"
edgers are standard with two release handles
|
Feed Rolls and Press Rolls:
- Two 5" diameter machine-cut infeed and two 5" diameter
machine-cut outfeed bottom rolls connected by a roller chain
drive
- Feed rolls mounted with 1 15/16" four-bolt flange bearings
- Hydraulic feed with variable control
- Two 8" diameter (Schedule 80 pipe with 1/2" wall) overhead
press rolls with 1 7/16" shafts
- Press roll mounted with 1 7/16" two-bolt flange bearings
- Standard Hydraulic press roll lift with foot-pedal control or push
button
- Optional automatic press roll lift with photoelectric eyes
- Complete set of anti-kickback fingers with release handle, 48"
edgers are standard with two release handles
|
Saws:
- 20" inserted tooth F pattern saw, 8 gauge with 18 teeth, 9/32"
kerf
- 20" carbide saws, 8 gauge with 18 teeth, 0.245"
kerf
- Saws have 3 1/4" eye with 9/16" pin holes on a 4"
circle
- Rim speed of saw, 10,320 ft./min.
|
Saws:
- 22" inserted tooth F pattern saw, 8 gauge with 18 teeth, 9/32"
kerf
- 22" carbide saws, 7 gauge with 20 teeth, 0.260"
kerf
- Saws have 3 1/4" eye with 9/16" pin holes on a 4"
circle
- Rim speed of saw, 11,350 ft./min.
|
Saws:
- 24" inserted tooth F pattern saw, 8 gauge with 20 teeth, 9/32"
kerf
- 24" carbide saws, 7 gauge with 20 teeth, 0.280"
kerf
- Saws have 3 1/4" eye with 9/16" pin holes on a 4"
circle
- Rim speed of saw, 10,405 ft./min.
|
Saw Shift:
- Stationary saw collars
- 1-saw lever shift (hand shift)
- 1-saw hydraulic shift
- 2-saw hydraulic unison shift (allows for use of electronic
setworks)
|
Saw Shift:
- Stationary saw collars
- 1-saw lever shift (hand shift)
- 1-saw hydraulic shift
- 2-saw hydraulic unison shift (allows for use of electronic
setworks)
|
Saw Shift:
- Stationary saw collars
- 1-saw lever shift (hand shift)
- 1-saw hydraulic shift
- 2-saw hydraulic unison shift (allows for use of electronic
setworks)
|
Capacity:
- Available in 36", 42", and 48" widths
- Cut depth from 1" to 6"
|
Capacity:
- Available in 36", 42", and 48" widths
- Cut depth from 1" to 7"
|
Capacity:
- Available in 36", 42", and 48" widths
- Cut depth from 1" to 8 1/2"
|
| Mandrel Speed Recommended:
|
Mandrel Speed Recommended:
|
Mandrel Speed Recommended:
|
Power Required:
- Power requirements will vary based on the number of saws and the
depth of the cut (60-hp to 200-hp)
|
Power Required:
- Power requirements will vary based on the number of saws and the
depth of the cut (60-hp to 200-hp)
|
Power Required:
- Power requirements will vary based on the number of saws and the
depth of the cut (60-hp to 200-hp)
|
Optional Equipment:
- Lumber Shift Chains, hydraulic drive and pneumatic lift
- Pneumatic holdover
- Variable speed hydraulic feed
- Electronic Setworks, to be used with unison shifting saws only
- Dial Figure Scale
- Infeed and Outfeed table built to customer specifications
- Laser lights
- Stationary or Flip-down fence on infeed table
- Saw dust blower
- Live outfeed rolls
- Tailing devices, electric drive, with narrow or wide belts
- Electric motor, starter, and v-belt drive
|
Optional Equipment:
- Lumber Shift Chains, hydraulic drive and pneumatic lift
- Pneumatic holdover
- Variable speed hydraulic feed
- Electronic Setworks, to be used with unison shifting saws only
- Dial Figure Scale
- Infeed and Outfeed table built to customer specifications
- Laser lights
- Stationary or Flip-down fence on infeed table
- Saw dust blower
- Live outfeed rolls
- Tailing devices, electric drive, with narrow or wide belts
- Electric motor, starter, and v-belt drive
|
Optional Equipment:
- Lumber Shift Chains, hydraulic drive and pneumatic lift
- Pneumatic holdover
- Variable speed hydraulic feed
- Electronic Setworks, to be used with unison shifting saws only
- Dial Figure Scale
- Infeed and Outfeed table built to customer specifications
- Laser lights
- Stationary or Flip-down fence on infeed table
- Saw dust blower
- Live outfeed rolls
- Tailing devices, electric drive, with narrow or wide belts
- Electric motor, starter, and v-belt drive
|
Meadows Mills, Inc. is
proud to introduce our new line of combination edgers. We have
combined the expertise of Meadows Mills, Inc., with 101 years of experience,
with the expertise of Miner Edger, with 79 years of experience, to build a line
of revolutionary new machines. Our 6" Spartan, 7" Trojan, and 8
1/2" Hercules offer rugged construction with a reasonable price. Our
6", 7", and 8 1/2" edgers are available in 36", 42", and 48"
widths. The chart below provides a quick reference of the features on
each of our combination edgers. If you have further questions or wish to
inquire about prices please contact Bob, Brian, or Robert at 1-800-626-2282 or
336-838-2282.